<nobr id="vjr5t"></nobr>

<ins id="vjr5t"><th id="vjr5t"><mark id="vjr5t"></mark></th></ins>

<del id="vjr5t"><span id="vjr5t"></span></del>

      <menuitem id="vjr5t"></menuitem>
        <dfn id="vjr5t"></dfn>
          <delect id="vjr5t"><pre id="vjr5t"></pre></delect>

          簡體中文 | English
          SEARCH:
          Home About us Products Press Room Service Certificate Case Show Technical Support Contact Us
          You are located : Home > Products > Pipe Bending Machine >
           
          Medium frequency pipe bender factory
          he first is the elbow of the pipe bender.Elbows placed for a long time should be checked regularly.The surface of some exposed elbow should be kept clean daily, clean up dirt in time, store in a ventilated and dry place indoors, keep the elbow dry and tidy,
           
          If you can envision it,We can supply it. E-mail:15230713671@163.com
          Description Specification Consulting  
          Medium frequency pipe bender factory

          The daily use and maintenance of each part of the intermediate frequency pipe bender are different.Different parts of the relative maintenance method is also different.When installing the pipe bender, the elbow and the elbow can be directly installed on the pipe bender road according to the specified connection mode.

          The first is the elbow of the pipe bender.Elbows placed for a long time should be checked regularly.The surface of some exposed elbow should be kept clean daily, clean up dirt in time, store in a ventilated and dry place indoors, keep the elbow dry and tidy, keep the pipe clean and tidy, and store it accurately according to the storage method provided by the manufacturer.

          It is also important to note that the elbow and elbow of the pipe bender can only be installed horizontally, because the medium of the elbow is upstream along the main valve disc.

          In addition, if the bending forming speed of the pipe bender is too fast, it is easy to cause the bending part of the pipe to be flat, and the bending degree can not meet the requirements.If the speed is too slow, it is easy to cause wrinkle or deformation of the catheter.In general, there is no special provision for the installation position of the elbow. It can be placed in any position of the pipeline, as long as it is convenient to operate and check.The fullness requirement of R and R point in bending radian of pipe bender is not too high, and the lining diameter should be provided at bending radian points.Double-head pipe bender can not add mandrel when bending pipe, so for the general requirements of bending radian plumpness of the pipe is not feasible, so we say that the bending pipe of the head pipe bender is mainly in the furniture manufacturing industry.When we process the die, we want to do the reverse deformation of the knot die, so that the inner arc of the curved pipe will be strengthened and the pressure resistance of the pipe will be improved.

          The company mainly produces various types of medium frequency pipe bender, medium frequency elbow machine, medium frequency pipe expanding machine, tee machine, press, beveling machine and other above pipe fittings equipment mold.Welcome the customer need to inquire order!

          Pipe bender equipment

          Pipe bender equipment is a kind of pipe bender production equipment, including hydraulic pipe bender, automatic pipe bender and so on.Choose different bending equipment according to customer needs.Pipe bending equipment is widely used in industrial equipment, a variety of production, processing and design need to use the bending equipment produced by our company.

          Pipe bending equipment in the work is mainly through the balance between the fulcrum and the force to construct the bending moment, so that the processed objects appear plastic deformation.In the pipe bending work, the use of hydraulic cylinder to promote the outer edge of the steel pipe close to the upper die, so that the upper die is fixed in the middle of the frame, fixture is placed at the end of the pipe bending equipment, the steel pipe will be clamped and fixed during operation.The lower die of the bending equipment is in the front, and the processing of the steel pipe can be introduced into the front from the back of the bending equipment, and then the inner tube is installed in the inner wall of the steel pipe, so that the steel pipe is not easy to deformation.Then it shows the gradual bending forming along the curve of the upper die.When the tensile stress of the lower wall of the steel pipe reaches the critical deformation time, the plastic deformation of the pipe will appear.

          In daily use, there will be some problems with the pipe bender. The main reason is that when the machine is bending the pipe, the metal circular saw is used to cut the pipe, which will leave a lot of small iron pins. It seems that the small iron pins left when cleaning the pipe bending can avoid a lot of problems with the pipe bender.Therefore, special attention should be paid to the small iron pin in the daily cleaning to ensure the normal working efficiency of the pipe bender.

          Pipe bender mainly uses oil pump to input hydraulic oil and solenoid valve to provide hydraulic power.So most of the iron pin into the tank after we will make the inside of the inlet pipe of the filter to filter out, but also there will be a small iron pin will enter into the oil pump, this is inhaled into the oil pump iron pin will enter into the solenoid valve, and the iron pin because can't flow in the solenoid valve force result in because of the electromagnetic valve plug,Because the oil can not flow, there will be a pair of action failure, resulting in the pipe bender can not work normally.

          The above briefly introduces the causes of the problems in the use of the pipe bender.

          445-444.

          Related Products
          • Pipe Bending Machine

          • medium frequency...

          • induction heatin...

          • hot forming pip...

           
          New Products
          - Medium frequency...
          - Medium frequency...
          - 168 intermediate...
          - Austrian radio ...
          - Customized mediu...
          - Making elbow machine
          - Standard elbow machine
          Top Products
          - Automatic Triple...
          - Automatic Double...
          - Hydraulic Press
          - Elbow Cold Forming Machine
          - Elbow Hot Forming Machine
          - Single-Head Pipe...
          - Pipe Bending Machine
          Hot Products
          - Automatic Triple...
          - Automatic Double...
          - Hydraulic Press
          - Elbow Cold Forming Machine
          - Elbow Hot Forming Machine
          - Single-Head Pipe...
          - Pipe Bending Machine
          Quick to find the product information
          ?
          Contact us
          Cangzhou Aocheng Machinery Equipment co., LTD.
          Address : Bobei Industrial Zone, Mengcun Hui Autonomous County, Cangzhou City, Hebei Province, China
          Mobile : +86-15230713671
          Fax : +86-317-6218625
          E-mail : 15230713671@163.com
          Skype : zhiguang.wu
          About Us |  Products |  Order Online |  Contact Us Copyright © Elbow Machine,Elbow Forming Machine,Tee Machine All Rights Reserved manage
             
          亚洲另类欧美小说图片区,亚洲另类图片专区,亚洲另类一区二区,亚洲乱码一区二区在线观看,亚洲乱色伦图片区小说 <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>